Unofficial File parts/s/20460s03.dat
File Header:
0 ~Minifig Leg Left with Boots Lower without Front and Side
0 Name: s\20460s03.dat
0 Author: Philippe Hurbain [Philo]
0 !LDRAW_ORG Unofficial_Subpart
0 !LICENSE Redistributable under CCAL version 2.0 : see CAreadme.txt
0 BFC CERTIFY CCW
Status:
Needs admin review. (CCX)
Size: 6293 bytes
Reviewers' certifications:
GeraldLasser=certify MagFors=certify Steffen=novote
Required (unofficial) subfiles:
(none)
Related (unofficial) subfiles:
2 subfiles aren't certified. (SSX)File reviews and updates:
At Wed Jan 2 06:30:29 2019 part 'parts/s/24060s03.dat' was renamed to 'parts/s/20460s03.dat'.
At Fri Jan 4 20:35:01 2019, the following review was posted:
Reviewer: MagFors
Certification: novote
Comments:
The inside of the lower part looks like this:
2 4 8 12 -.1 8 12 6
4 13 8 12 -.1 5 14 -2 5 14 6 8 12 6
1 13 4.5 14 2 0 0 .5 0 -1 0 4 0 0 rect.dat
2 4 12 12 6 12 12 -.1
4 13 12 12 6 15 14 6 15 14 -2 12 12 -.1
1 13 15.5 14 2 0 0 -.5 0 -1 0 -4 0 0 rect.dat
4 13 8 12 -.1 8 12 6 12 12 6 12 12 -.1
4 13 8 12 -.1 12 12 -.1 15 14 -2 5 14 -2
2 4 5 14 6 8 12 6
2 4 8 12 6 12 12 6
2 4 12 12 6 15 14 6
5 4 12 12 -.1 8 12 -.1 8 12 6 5 14 -2
5 4 8 12 -.1 5 14 -2 5 14 6 15 14 -2
5 4 12 12 -.1 15 14 -2 15 14 6 5 14 -2
5 4 5 14 -2 15 14 -2 16 22.5 -2 12 12 -.1
Reviewer: MagFors
Certification: novote
Comments:
The inside of the lower part looks like this:
2 4 8 12 -.1 8 12 6
4 13 8 12 -.1 5 14 -2 5 14 6 8 12 6
1 13 4.5 14 2 0 0 .5 0 -1 0 4 0 0 rect.dat
2 4 12 12 6 12 12 -.1
4 13 12 12 6 15 14 6 15 14 -2 12 12 -.1
1 13 15.5 14 2 0 0 -.5 0 -1 0 -4 0 0 rect.dat
4 13 8 12 -.1 8 12 6 12 12 6 12 12 -.1
4 13 8 12 -.1 12 12 -.1 15 14 -2 5 14 -2
2 4 5 14 6 8 12 6
2 4 8 12 6 12 12 6
2 4 12 12 6 15 14 6
5 4 12 12 -.1 8 12 -.1 8 12 6 5 14 -2
5 4 8 12 -.1 5 14 -2 5 14 6 15 14 -2
5 4 12 12 -.1 15 14 -2 15 14 6 5 14 -2
5 4 5 14 -2 15 14 -2 16 22.5 -2 12 12 -.1
At Sat Jan 5 14:35:01 2019, a new version of the file was submitted.
Submitted by: Philo
Comments:
Thanks Magnus. Applied.
Existing certification-votes were deleted.
Submitted by: Philo
Comments:
Thanks Magnus. Applied.
Existing certification-votes were deleted.
At Sun Jan 20 22:05:01 2019, the following review was posted:
Reviewer: MagFors
Certification: certify
Comments:
It is actually some sort of surface curved in three directions, but I think this very simplified solution works.
Reviewer: MagFors
Certification: certify
Comments:
It is actually some sort of surface curved in three directions, but I think this very simplified solution works.
At Tue Jun 11 09:50:01 2019, the following review was posted:
Reviewer: GeraldLasser
Certification: certify
No comments were posted with this review.
Reviewer: GeraldLasser
Certification: certify
No comments were posted with this review.
At Wed Jun 12 01:55:02 2019, the following review was posted:
Reviewer: Steffen
Certification: hold
Comments:
something is wrong with the condlines when you
look at the part from below.
when I do that, 4 condlines are not visible where they should be.
when I enable display of all condlines, they are there.
this means that the control points are broken of 4 condlines
Reviewer: Steffen
Certification: hold
Comments:
something is wrong with the condlines when you
look at the part from below.
when I do that, 4 condlines are not visible where they should be.
when I enable display of all condlines, they are there.
this means that the control points are broken of 4 condlines
At Thu Jul 4 23:15:01 2019, the following review was posted:
Reviewer: GeraldLasser
Certification: certify
Comments:
@Steffen, in my opinion the cond-lines are ok. Looking from the bottom, you should not see them as they shall smoothen the inside (see the complete assembly 20460, where this works well)
The condlines work also if you look in LDPE at the subpart. IMHO there is no way you will ever see the actual line, you only see the smoothing
Reviewer: GeraldLasser
Certification: certify
Comments:
@Steffen, in my opinion the cond-lines are ok. Looking from the bottom, you should not see them as they shall smoothen the inside (see the complete assembly 20460, where this works well)
The condlines work also if you look in LDPE at the subpart. IMHO there is no way you will ever see the actual line, you only see the smoothing
At Fri Jul 5 15:10:02 2019, the following review was posted:
Reviewer: MagFors
Certification: certify
Comments:
Gerald is correct. You will never see these cond-lines.
Philo used my code, above, and as I said, it is very simplified, but working correctly.
When looking inside a real part I see a smooth surface, and some parallel edges.
Reviewer: MagFors
Certification: certify
Comments:
Gerald is correct. You will never see these cond-lines.
Philo used my code, above, and as I said, it is very simplified, but working correctly.
When looking inside a real part I see a smooth surface, and some parallel edges.
At Fri Jul 5 18:00:02 2019, the following review was posted:
Reviewer: Steffen
Certification: novote
Comments:
downgrading to novote
Reviewer: Steffen
Certification: novote
Comments:
downgrading to novote
3D View