Unofficial File parts/83496.dat
part image
File Header:
0 Tile  4 x  8 Inverted
0 Name: 83496.dat
0 Author: Gerald Lasser [GeraldLasser]
0 !LDRAW_ORG Unofficial_Part
0 !LICENSE Redistributable under CCAL version 2.0 : see CAreadme.txt

0 BFC CERTIFY CCW

Status:
1 subfile isn't certified. (CCSN)
Size: 296 bytes
Reviewers' certifications:
GeraldLasser=novote
MMR1988=certify
MagFors=novote
OrionP=novote
Philo=certify
Required (unofficial) subfiles:
~Tile 4 x 8 Inverted without Patternable Surface
Status: 1 subfile isn't certified. (CCSN)
Related (unofficial) subfiles:
(none)
File reviews and updates:
At Mon Feb 28 10:30:01 2022, the file was initially submitted.
Submitted by: GeraldLasser
Comments:
I hope I spotted the number right!

At Wed Mar 9 08:30:01 2022, the following review was posted:

Reviewer: Philo
Certification: certify
Comments:
You did ;)

At Mon Mar 14 20:40:01 2022, the following review was posted:

Reviewer: MMR1988
Certification: certify
No comments were posted with this review.

At Thu Jun 23 14:10:01 2022, the following review was posted:

Reviewer: MagFors
Certification: hold
Comments:
What makes this a Tile?
IMO, the description should be "Plate 4 x 8 Inverted with Groove"
11203 is official as "Plate 2 x 2 Inverted with Groove"

Remember: If studs on top, it's a Plate.

At Thu Jun 23 21:35:01 2022, the following review was posted:

Reviewer: GeraldLasser
Certification: novote
Comments:
but then, what makes it an inverted plate?

it could be a
Tile, Bottom
Rebrickable calls it Tile, Special
Plate with flat bottom




At Fri Jun 24 00:00:01 2022, the following review was posted:

Reviewer: OrionP
Certification: novote
Comments:
The already official part of this type is a Plate. If we want to deviate from that, a discussion needs to happen.

At Fri Jun 24 07:15:01 2022, the following review was posted:

Reviewer: MagFors
Certification: hold
Comments:
I could accept this as a Tile, but only if we also flip it, and 11203, upside down.
But the currect orientation is dictated by another rule that state that the stud has to be on the top surface.
If/when these flat parts gets printed no one will ever see it since it will end up on the bottom surface.
At Fri Jun 24 08:20:02 2022, the following review was posted:

Reviewer: GeraldLasser
Certification: novote
Comments:
concerning such printed parts, where there are already some available (2x2) I had the suggestion to render them upside down and present the picture with an icon that shows the rotated orientation.

https://forums.ldraw.org/thread-24601.html?highlight=11203

At Fri Jun 24 08:40:01 2022, the following review was posted:

Reviewer: GeraldLasser
Certification: novote
Comments:
We do have a similar approach already with the panel 4215a, where the rendering is done different than the other parts

At Fri Jun 24 14:55:01 2022, the following review was posted:

Reviewer: OrionP
Certification: novote
Comments:
Since all the other sites call this "Tile X x X Inverted", I feel we should too.

At Wed Jun 29 02:35:01 2022, the following review was posted:

Reviewer: OrionP
Certification: novote
Comments:
Per forum discussion this will remain as "Tile". Additionally, the orientation is consistent with 35459 and 11203 and should not change.

At Wed Jun 29 16:50:01 2022, the following review was posted:

Reviewer: MagFors
Certification: novote
Comments:
Retracting the Hold vote, and maybe we should remove the "with Groove".

At Thu Jun 30 14:25:01 2022 a Parts Tracker Admin edited the header.