Unofficial File parts/51663.dat
part image
File Header:
0 Technic Bionicle Weapon Minifig Staff Whenua (Needs Work)
0 Name: 51663.dat
0 Author: Michael Heidemann [mikeheide]
0 !LDRAW_ORG Unofficial_Part
0 !LICENSE Redistributable under CCAL version 2.0 : see CAreadme.txt

0 BFC CERTIFY CCW

0 !CATEGORY Minifig Accessory

0 // Needs Work: decoration on the bar has to be modelled
0 //             ribs on underside of curved part have to be modelled

0 !HISTORY 2012-03-24 [Steffen] BFCed, some corrections

Status:
1 'hold' vote. (HN)
Size: 8918 bytes
Reviewers' certifications:
Steffen=hold
dulcaoin=novote
Required (unofficial) subfiles:
(none)
Related (unofficial) subfiles:
(none)
File reviews and updates:
At Sun Feb 18 17:28:33 2007, the file was initially submitted.
Submitted by: mikeheide
At Sat Dec 11 10:05:41 2010, the following review was posted:

Reviewer: Steffen
Certification: novote
Comments:
suggest BFCing

At Wed Dec 28 18:25:03 2011, the following review was posted:

Reviewer: Steffen
Certification: novote
Comments:
comparing this with
http://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/32559.dat
, I think that this file needs re-orientation

At Sun Mar 11 14:25:02 2012, the following review was posted:

Reviewer: Steffen
Certification: novote
Comments:
reconsidered. both orientations are fine probably.
but this file should get BFCed.

At Sat Mar 24 14:05:05 2012, a new version of the file was submitted.
Submitted by: Steffen
Comments:
BFCed, some corrections

Existing certification-votes were deleted.
At Sat Mar 24 14:05:07 2012, a new version of the file was submitted.
Submitted by: Steffen
Comments:
BFCed, some corrections

At Sat Mar 24 14:10:03 2012, the following review was posted:

Reviewer: Steffen
Certification: hold
Comments:
The 2 files 51663.dat and 51643.dat each have 2 boxes
in their middle, with attached cylinders.
However, the placement of these boxes in the current versions
on the PT mismatch. One of them must be wrong I think.

At Thu Dec 13 21:15:01 2018, the following review was posted:

Reviewer: dulcaoin
Certification: novote
Comments:
Intrigued by Steffan's comment, I pulled out various tools of this type. For future reference:

ALL of
51641 TOOL W. DOUBL. SHAFT NO.1
51642 TOOL W. DOUBL. SHAFT NO.2
51643 TOOL W. DOUBL. SHAFT NO.3
51644 TOOL W. DOUBL. SHAFT NO.4
51645 TOOL W. DOUBL. SHAFT NO.5
and
51663 TOOL W. DOUBL. SHAFT NO.6

have the same spacing on the double shafts: center-line to center-line is the spacing of 5M (or 5L if you prefer, or 5 studs). If my math is right, that's a center-to-center spacing of 100 LDU.

I didn't actually check the two parts. :-}

At Thu Dec 13 21:15:01 2018, the following review was posted:

Reviewer: dulcaoin
Certification: novote
Comments:
(by which I mean, I did not check the two .DATs to see which of either (or both) is out of proper alignment)