Unofficial File parts/40341.dat
part image
File Header:
0 Technic Bionicle Weapon Circular Saw with Axle 6L
0 Name: 40341.dat
0 Author: Santeri Piippo [arezey]
0 !LDRAW_ORG Unofficial_Part
0 !LICENSE Redistributable under CCAL version 2.0 : see CAreadme.txt

0 BFC CERTIFY CCW

Status:
2 subfiles aren't certified. (SSX)
Size: 29155 bytes
Reviewers' certifications:
MagFors=novote
Philo=novote
arezey=novote
Required (unofficial) subfiles:
Related (unofficial) subfiles:
(none)
File reviews and updates:
At Sat May 18 18:25:01 2013, the file was initially submitted.
Submitted by: arezey
Comments:
First LDForge part. :)

The catalyst reason for modeling this right now was to give the thing a stress-test (which it went over rather well). This one is quite high up on my favorites list anyway. Now I can make a 3D model of the Raptor!

Do note: DATHeader doesn't seem to run on my kubuntu system so I cannot run that. If someone could pass this file and the subfiles through DATHeader and re-submit if there was any fixing to do, that'd be great.


At Sat May 18 18:55:01 2013, the following review was posted:

Reviewer: mikeheide
Certification: novote
Comments:
Line 526: Not scalable primitive is scaled. 1 16 0 0 150 0 0 1 1 0 0 0 118 0 axlehol2.dat
Line 527: Not scalable primitive is scaled. 1 16 0 0 150 0 0 1 1 0 0 0 118 0 axlehol9.dat
Line 530: Incorrect use of only '0' for comments. 0 //


At Sat May 18 19:00:07 2013, a new version of the file was submitted.
Submitted by: arezey
Comments:
Should be fixed now.

Existing certification-votes were deleted.

At Sat May 18 19:25:02 2013, the following review was posted:

Reviewer: Philo
Certification: novote
Comments:
Hats off! (for the part and for the promizing LDForge !!!)

At Tue May 28 13:15:07 2013, the following review was posted:

Reviewer: Philo
Certification: novote
Comments:
Visually it seems pretty good, but when I run Edger2 on it to find orphan edges, I find several in areas where I wouldn't expect them, even with large tolerance. Could you have a closer look?


At Wed Jun 12 19:45:02 2013, the following review was posted:

Reviewer: arezey
Certification: novote
Comments:
I don't quite understand. Orphan edges? where?


At Wed Jun 12 20:30:03 2013, the following review was posted:

Reviewer: Philo
Certification: novote
Comments:
I meant unmatched edges, as shown by Edger2, using options "Expand subfiles" -s, precision -p 0.01, create only unmatched edges. You'll see red lines appearing in many places. Some are caused by a few T junctions (I don't mind so much), but other are not easy to explain (eg. between saw teeth). Maybe some imprecision in rotation values? Anyway, as I said, part _look_ ok, so I can happily live with that ;)


At Wed Jun 12 21:45:03 2013, the following review was posted:

Reviewer: arezey
Certification: novote
Comments:
Ah. that doesn't surprise me that much, could very well be imprecision. If someone wants to fix
that, go ahead but since it doesn't manifest in the part at all I find it too minor an issue.
I'd rather spend time getting new parts done as well as on LDForge.


At Wed Jun 12 22:00:06 2013, the following review was posted:

Reviewer: MagFors
Certification: novote
Comments:
Yes, I too seee those unmatched edges.
I think that many are caused by t-junctions in the tooth sub file
Edger also creates a lot of new cond-lines, both in the saw tooth and the saw blade.