Unofficial File parts/28424p01.dat
part image
File Header:
0 Minifig Police Hat Dark Blue with Hair Pulled Into Bun with Metallic Gold Badge Pattern
0 Name: 28424p01.dat
0 Author: Bertrand Lequy [Berth]
0 !LDRAW_ORG Unofficial_Part
0 !LICENSE Redistributable under CCAL version 2.0 : see CAreadme.txt

0 BFC CERTIFY CCW

0 !KEYWORDS Set 60143, Set 60141, Set 60140, Set 40372, Bricklink 28430pb02

Status:
6 subfiles aren't certified. (SSSSSSN)
Size: 622 bytes
Reviewers' certifications:
Berth=novote
Required (unofficial) subfiles:
Related (unofficial) subfiles:
(none)
File reviews and updates:
At Thu Apr 15 06:55:02 2021, the file was initially submitted.
Submitted by: Berth
At Wed Jun 2 18:40:01 2021, the following review was posted:

Reviewer: MagFors
Certification: hold
Comments:
The middle history line, (Rolf and digital-bricks ) is not needed. You should only edit it, with your name and preparation date.
That history comment is only needed in the base file, this file. Not in all of the following coloured parts.

In dual moulded parts the edge line between two coulours is not needed/wanted. In this case on the inside, between the hair and the hat.

p02 should not have gold buttons on the sides. They're also black.

You should not use pearl colours in a pattern. The printed sections here are Metallic gold, code 82.

Did you try to divide any of the sections into a left/right halves?
I think the rim around the hat could be divided, and reused mirrored.

Maybe the hair have to many edge lines? It is often better to have condlines on convex surfaces, and only have edge lines between.
At Sun Jun 6 11:15:01 2021, a new version of the file was submitted.
Submitted by: Berth
Existing certification-votes were deleted.
At Sun Jun 6 11:20:02 2021, the following review was posted:

Reviewer: Berth
Certification: novote
Comments:
The middle history line, (Rolf and digital-bricks ) is not needed. You should only edit it, with your name and preparation date.
That history comment is only needed in the base file, this file. Not in all of the following coloured parts. >>> done

In dual moulded parts the edge line between two coulours is not needed/wanted. In this case on the inside, between the hair and the hat. >>>done

p02 should not have gold buttons on the sides. They're also black.

You should not use pearl colours in a pattern. The printed sections here are Metallic gold, code 82.>>> done (changed the name too)

Did you try to divide any of the sections into a left/right halves?
I think the rim around the hat could be divided, and reused mirrored.>>> I tried the rim but it was impossible because of the hair on the left side but I divided the top part. I asked myself the question for the badge since it is symetrical, but is it worth it for such a small subpart ?

Maybe the hair have to many edge lines? It is often better to have condlines on convex surfaces, and only have edge lines between. >>> I don't know, I'm going to wait for an other review since it seems to need a load of work.

At Sun Jun 6 14:20:01 2021, the following review was posted:

Reviewer: MagFors
Certification: hold
Comments:
Some of the added condlines have very bad controlpoints.

I don't like the divided top subfile. I use the alternative config file with coloured edgelines, and it gives colour to the condlines to.
In this case, the added condlines in the "main assembly" gets the same colour as the hair.
e.g. yellow condlines on top of the blue hat, if the file is used coloured yellow.

At Sun Jun 6 15:45:01 2021, the following review was posted:

Reviewer: Berth
Certification: novote
Comments:
So, I should roll back on the top subpart.

I had issues when creating some of the condlines, and I must admit I'm never sure to add them correctly when neither LPE or Edger2manage to add them automaticaly.

At Sun Jun 6 16:15:02 2021, the following review was posted:

Reviewer: MagFors
Certification: hold
Comments:
Yes, please do.

Sound like like a settings issue. Are you using LETGUI, or Edger2 in LDPE?

At Sun Jun 6 17:15:01 2021, the following review was posted:

Reviewer: Berth
Certification: novote
Comments:
This time in LDPE

At Sun Jun 6 19:25:02 2021, a new version of the file was submitted.
Submitted by: Berth
Existing certification-votes were deleted.
At Sun Jun 6 19:25:02 2021, the following review was posted:

Reviewer: Berth
Certification: novote
Comments:
All files updated