Unofficial File p/phandle1.dat
part image
File Header:
0 Bar Handle Attachment with Open Side
0 Name: phandle1.dat
0 Author: Gerald Lasser [GeraldLasser]
0 !LDRAW_ORG Unofficial_Primitive
0 !LICENSE Redistributable under CCAL version 2.0 : see CAreadme.txt

0 BFC CERTIFY CCW

Status:
Needs admin review. (CCN)
Size: 1047 bytes
Reviewers' certifications:
GeraldLasser=novote
MMR1988=certify
MagFors=certify
Philo=novote
mkennedy=novote
Required (unofficial) subfiles:
(none)
Related (unofficial) subfiles:
Plate 1 x 1 with Handles on Opposite Ends
Status: 1 subfile isn't certified. (CSN)
Download: parts/78257.dat
~Windscreen 10 x 4 x 2 with Handle - Half
Status: 1 subfile isn't certified. (CSN)
File reviews and updates:
At Wed Jul 14 09:15:01 2021, the file was initially submitted.
Submitted by: GeraldLasser
Comments:
I got tired of copying this section around for every plate with a handle, so I made it into a primitive as I couldn't find and existing one.

it is aligned like CLIP3.DAT

I reduced TJ and unnecessary vertices that are present along a straight edge usually.

What do you think? Shall we keep it?

At Wed Jul 14 13:10:01 2021, the following review was posted:

Reviewer: Philo
Certification: novote
Comments:
Yes, I think it's fine. Origin is somewhat questionable (though usable!), but it fits clip3.

At Tue Aug 31 20:45:02 2021, the following review was posted:

Reviewer: MagFors
Certification: novote
Comments:
Should all the parts that could use this prim be reworked?
Like these: 60478, 48336, 18649, 26047, and there must be more. Like windscreens.
And how about 2540?

At Sun Sep 26 08:40:02 2021, the following review was posted:

Reviewer: MagFors
Certification: certify
No comments were posted with this review.

At Sun Sep 26 11:40:01 2021, the following review was posted:

Reviewer: GeraldLasser
Certification: novote
Comments:
or shall we change it to a holw on both sides? to fit also 2540 and the HP-Bookcovers? makes sense

So two Prims,
- one open to both sides,
- one open towards one side only

At Wed Nov 3 20:40:01 2021, the following review was posted:

Reviewer: MagFors
Certification: certify
Comments:
bump

At Sat Nov 6 19:40:02 2021, the following review was posted:

Reviewer: Philo
Certification: novote
Comments:
Magnus reminded me of (mostly) the same primitive that I made but didn't use 'cause the target part was already done... I'm OK with this one, but I really think that the origin I used is much more practical...
One little thing: Using a rect there prevent smooth shading because of limited precision, using quad + lines would be better!
1 16 0 0 7.8015 0 0 3 0 1 0 -2.1985 0 0 rect2p.dat
Since this prim has no connectivity, it's more a convenience than anything else, reworking old parts is not useful imho.

At Sun Jan 16 16:10:01 2022, the following review was posted:

Reviewer: mkennedy
Certification: novote
Comments:
If you fill in the hole it may be usable in more parts.
This could actually qualify for being made a primitive.

At Sun Jan 16 16:10:01 2022, the following review was posted:

Reviewer: mkennedy
Certification: novote
Comments:
Just notices it's already classified as a primitive...

At Sun Jan 16 16:15:01 2022, the following review was posted:

Reviewer: mkennedy
Certification: novote
Comments:
May be able to use 11-16disc primitive?

At Sun Jan 23 16:45:01 2022, the following review was posted:

Reviewer: MMR1988
Certification: certify
Comments:
I wish you would unscale the chrd prim in y dimension.
1 16 -3 2 0 0 6 0 -6 0 0 0 0 6 3-16chrd.dat

I'm not happy with the origin but we use the same for clip prims...