Unofficial File parts/u9261.dat

Next File | Prev File | Download | Review | Edit | CA Header Edit | Events

File Header:

0 ~Turntable  4 x  4 Centre Connector Underside
0 Name: u9261.dat
0 Author: Max Martin Richter [MMR1988]
0 !LDRAW_ORG Unofficial_Part
0 !LICENSE Redistributable under CCAL version 2.0 : see CAreadme.txt

0 BFC CERTIFY CCW

0 !CMDLINE -c15

Status:
Certified! (ACCX)
Size: 1522 bytes

Reviewers' certifications:

MagFors=certify
cwdee=certify
mikeheide=certify

Required (unofficial) subfiles:

p/4-4rin30.dat	Ring 30 x 1.0	Certified! (ACCX)	Events
p/t01i3261.dat	Torus Inside 1 x 0.3261 x 1	Certified! (ACCX)	Events

Related (unofficial) files:

parts/3404bc01.dat	~Turntable 4 x 4 Dimpled Top w. Connector w. Black Inside	1 subfile isn't certified. (CCSX)	Events
parts/3404bc02.dat	~Turntable 4 x 4 Dimpled Top w. Connector w. Red Inside	1 subfile isn't certified. (CCSX)	Events
parts/3404dc01.dat	~Turntable 4 x 4 Round Top w. Connector w. Black Inside	1 subfile isn't certified. (CSX)	Events
parts/3404dc02.dat	~Turntable 4 x 4 Round Top w. Connector w. Red Inside	1 subfile isn't certified. (CCSX)	Events

File reviews and updates:

At Wed Dec 12 10:50:04 2012, the file was initially submitted.
Submitted by: MMR1988
======================================================================
At Wed Dec 12 12:40:05 2012, a new version of the file was submitted.
Submitted by: MMR1988
Comments:
Part was 0.25 LDU to long.

======================================================================
At Wed Dec 12 13:05:04 2012, the following review was posted:

Reviewer: Philo
Certification: novote
Comments:
"Part was 0.25 LDU to long".
I think you should try to simplify things instead to stick very strictly to reality (I know, simplifying things is sometimes... difficult!).
For example, the outside cylinder has a 19.875 ldu radius, I'm pretty sure that rounding that to 20ldu wouldn't harm, but would avoid the huge number of rings needed to match this odd value! File size doesen't matter these days, but facet count still does!.
In the same spirit, the 46/15 torus you use is far less reusable than a 3/1 torus, especially since t01i3333.dat already exist in library. And I am sure you can't measure a torus with precision!!!

======================================================================
At Wed Dec 12 13:20:02 2012, the following review was posted:

Reviewer: MMR1988
Certification: novote
Comments:
The radius of 19.875 is in fact odd for getting it with rings. But let me explain, why I didn't use the 20 LDU: there is a visible gap between this part and the turntable base in reality. This part can also move a bit, when it is in the turntable base.
I can go with your torus suggestion. Let me see, what I can do here.


======================================================================
At Wed Dec 12 14:10:03 2012, the following review was posted:

Reviewer: Philo
Certification: novote
Comments:
"But let me explain, why I didn't use the 20 LDU: there is a visible gap between this part and the turntable base in reality"
OK. This also adds a small benefit: when rotated at odd angle, there is less or no overlap with turntable base.
Don't loose time if you feel you did the right thing, I just wanted to attract your attention on those matters...


======================================================================
At Wed Dec 12 18:25:03 2012, the following review was posted:

Reviewer: MagFors
Certification: hold
Comments:
I can't get these to work properly.
1 36 0 0 0 1 0 0 0 1 0 0 0 1 3404d.dat
1 4 0 4 0 1 0 0 0 1 0 0 0 1 u9260.dat
1 15 0 4 0 1 0 0 0 1 0 0 0 1 u9261.dat
1 40 0 0 0 1 0 0 0 1 0 0 0 1 3404e.dat
1 14 0 24 0 1 0 0 0 1 0 0 0 1 stug-4x4.dat

u9162 and the two lower parts, 3404e and 3404c, don't fit each other.
And the subfile to 3404c and 3404e don't fit the stud grid.

======================================================================
At Wed Dec 12 23:25:03 2012, a new version of the file was submitted.
Submitted by: MMR1988
Comments:
Changed the origin

Existing certification-votes were deleted.
======================================================================
At Mon Jan 7 23:15:08 2013, the following review was posted:

Reviewer: MagFors
Certification: certify
No comments were posted with this review.

======================================================================
At Mon Apr 1 07:10:04 2013 a Parts Tracker Admin edited the header.
======================================================================
At Mon Apr 1 08:30:04 2013, the following review was posted:

Reviewer: mikeheide
Certification: certify
No comments were posted with this review.

======================================================================
At Thu Apr 4 05:05:04 2013, the following review was posted:

Reviewer: cwdee
Certification: certify
No comments were posted with this review.