Unofficial File parts/47116.dat

Next File | Prev File | Download | Review | Edit | CA Header Edit | Events

File Header:

0 Brick 12 x 24 with Pegs
0 Name: 47116.dat
0 Author: Greg Teft [gregteft]
0 !LDRAW_ORG Unofficial_Part
0 !LICENSE Redistributable under CCAL version 2.0 : see CAreadme.txt

0 BFC CERTIFY CCW

0 !KEYWORDS Belville, basebrick

Status:
5 subfiles aren't certified. (CCSSSSSX)
Size: 5804 bytes

Reviewers' certifications:

MagFors=certify
mikeheide=certify

Required (unofficial) subfiles:

parts/s/47116s01.dat	~Brick 12 x 24 with Pegs - Axlehole and Flanged Support Ring	Needs admin review. (CCX)	Events
parts/s/47116s02.dat	~Brick 12 x 24 with Pegs - Corner Stud Tubes and Flush H-Ribs	Needs admin review. (CCX)	Events
parts/s/47116s03.dat	~Brick 12 x 24 with Pegs - Edge Stud Tubes and Flush H-Ribs	Needs admin review. (CCX)	Events
parts/s/47116s04.dat	~Brick 12 x 24 with Pegs - Triple Stud Tubes and Flush H-Ribs	Needs admin review. (CCX)	Events
parts/s/47116s05.dat	~Brick 12 x 24 with Pegs - Double Stud Tubes and Flush H-Ribs	Needs admin review. (CCX)	Events

Related (unofficial) files:
(none)

File reviews and updates:

At Sat Apr 28 21:45:07 2012, the file was initially submitted.
Submitted by: gregteft
Comments:
Finally settled on an arrangement. The sub-parts would be reusable in this configuration with a good balance between number of placements and size of files.

======================================================================
At Wed May 9 22:05:02 2012, the following review was posted:

Reviewer: MagFors
Certification: novote
Comments:
Intresting set of subfiles.

It's allways a good idea to avoid t-junctions, byt here it results in this:
Line 95: Colinear vertices found. 3 16 240 24 120 81 24 116 79 24 116
Line 97: Colinear vertices found. 3 16 240 24 120 41 24 116 39 24 116
Line 101: Colinear vertices found. 3 16 -39 24 116 -41 24 116 -240 24 120
Line 103: Colinear vertices found. 3 16 -79 24 116 -81 24 116 -240 24 120
Line 121: Colinear vertices found. 3 16 -240 24 -120 -81 24 -116 -79 24 -116
Line 123: Colinear vertices found. 3 16 -240 24 -120 -41 24 -116 -39 24 -116
Line 127: Colinear vertices found. 3 16 39 24 -116 41 24 -116 240 24 -120
Line 129: Colinear vertices found. 3 16 79 24 -116 81 24 -116 240 24 -120

I think it would be OK with just four quads around this base surface.

======================================================================
At Thu May 10 01:30:03 2012, the following review was posted:

Reviewer: gregteft
Certification: novote
Comments:
I went back and forth on the bottom edges. When I used just the four quads the T's really stood out in LDView with red back-faces turned on. I did note that the angles here are less than LDDP's default tolerance, but are greater than .01, and the shortest edges are 2 LDU wide.

======================================================================
At Thu May 10 21:05:02 2012, the following review was posted:

Reviewer: MagFors
Certification: novote
Comments:
LDraw specs says:
"must not be greater than 179.9 degrees or smaller than 0.025 degrees".

======================================================================
At Thu Jun 7 02:10:02 2012, a new version of the file was submitted.
Submitted by: gregteft
Comments:
resolved by adding seam at x=0, no T's, no extremely acute angles.

Existing certification-votes were deleted.
======================================================================
At Mon Jun 11 13:25:02 2012 a Parts Tracker Admin edited the header.
======================================================================
At Mon Jun 11 19:25:02 2012, the following review was posted:

Reviewer: MagFors
Certification: certify
No comments were posted with this review.

======================================================================
At Sat Mar 16 09:20:03 2013, the following review was posted:

Reviewer: mikeheide
Certification: certify
No comments were posted with this review.