Unofficial File parts/30535.dat

Next File | Prev File | Download | Review | Edit | CA Header Edit | Events

File Header:

0 Brick  2 x  4 x  4 with Propellor Housing
0 Name: 30535.dat
0 Author: John Riley [jriley]
0 !LDRAW_ORG Unofficial_Part
0 !LICENSE Redistributable under CCAL version 2.0 : see CAreadme.txt

0 BFC CERTIFY CCW

0 !KEYWORDS engine, rotor, propulsion, intake

0 !HISTORY 2007-10-07 [mikeheide] fixed all 24 lines
0 !HISTORY 2009-01-29 [mikeheide] changed header uses 4-4ring4.dat
0 !HISTORY 2013-03-11 [mikeheide] Changed two edgelines, changed two 4-4cyli.dat to 3-4cyli.dat like requested.

Status:
1 'hold' vote. (HX)
Size: 46079 bytes

Reviewers' certifications:

MMR1988=hold

Required (unofficial) subfiles:
(none)

Related (unofficial) files:
(none)

File reviews and updates:

At Sat May 17 18:00:01 2003, the file was initially submitted.
Submitted by: jriley
======================================================================
At Wed Jul 16 16:00:07 2003, a new version of the file was submitted.
Submitted by: jriley
Comments:
Changed name, added KEYWORDS statement

======================================================================
At Wed Jul 16 22:00:06 2003, the following review was posted:

Reviewer: Steffen
Certification: hold
Comments:
some identical lines

BFC error on left and right side at connector portion

======================================================================
At Fri Jul 18 15:00:02 2003, a new version of the file was submitted.
Submitted by: jriley
Comments:
corrected errors

Existing certification-votes were deleted.
======================================================================
At Sun Nov 30 16:44:09 2003, the following review was posted:

Reviewer: fwcain
Certification: novote
No comments were posted with this review.

======================================================================
At Sun Apr 4 12:26:02 2004, the following review was posted:

Reviewer: Steffen
Certification: certify
No comments were posted with this review.

======================================================================
At Thu Apr 15 02:20:02 2004, the following review was posted:

Reviewer: pneaster
Certification: hold
Comments:
Nice Job! However,
2 lines have stray ends. (They do not go where they should) They run on the z axis, low on the part, inside surfaces of the sloped areas.
2 24 -30 64.1858 10 -31 62.6892 -10
-> 2 24 -30 64.1858 10 -30 64.1858 -10
2 24 30 64.1858 10 31 62.6892 -10
-> 2 24 30 64.1858 10 30 64.1858 -10

Also, not as critical, there are 11 lines on each side(total of 22 lines) that cross the x-y plane that could be trimmed into two lines each.

======================================================================
At Sun Oct 7 20:36:02 2007, a new version of the file was submitted.
Submitted by: mikeheide
Comments:
fixed all mentioned lines.

Existing certification-votes were deleted.
======================================================================
At Tue Jan 6 11:30:16 2009, the following review was posted:

Reviewer: Steffen
Certification: hold
Comments:
spelling "propeller" should be changed to "propellor"
to match currently official parts naming

======================================================================
At Thu Jan 29 07:36:04 2009, a new version of the file was submitted.
Submitted by: mikeheide
Existing certification-votes were deleted.
======================================================================
At Wed Jun 3 21:40:11 2009, the following review was posted:

Reviewer: Steffen
Certification: hold
Comments:
Wow, a complex part, congratulations.
I found two minor issues that should be easy to solve:
a) I think that this quad and similar
4 16 -19.3649 37 -10 -35.0054 37 -10 -34.6076 35 -10 -20.8567 35 -10
is missing an edge where touching the outside round border
b) I think that this line
2 24 -35.0054 37 -18 -35.0054 47 -18
and similar is wrong

======================================================================
At Thu Jun 4 20:34:02 2009, the following review was posted:

Reviewer: mikeheide
Certification: novote
Comments:
"b) I think that this line 2 24 -35.0054 37 -18 -35.0054 47 -18 and similar is wrong" no, that lines are needed and ok.

Will try to solve the a) problem.

======================================================================
At Thu Jun 4 20:58:04 2009, a new version of the file was submitted.
Submitted by: mikeheide
Comments:
Added mentioned line and some adjustments of lines and added some edgelines.

Existing certification-votes were deleted.
======================================================================
At Fri Jun 19 23:32:01 2009, the following review was posted:

Reviewer: Steffen
Certification: novote
Comments:
this 4-4edge
1 16 -24 82 0 0 -15 0 10 0 0 0 0 -10 4-4edge.dat
pokes through on the underside

======================================================================
At Fri Jun 19 23:40:05 2009, the following review was posted:

Reviewer: Steffen
Certification: novote
Comments:
I still don't understand the line
2 24 35.0054 47 -18 35.0054 37 -18
It cuts straight through a quad, but where that quad
touches the outside wall, the edge is missing. hmmm

======================================================================
At Sat Jan 7 21:55:10 2012, the following review was posted:

Reviewer: timgould
Certification: hold
Comments:
This is such an amazing job I really don't want to hold it. But I must.

Missing some edge lines

http://www.brickshelf.com/gallery/timgould/LDraw/Review/30535001.png

and has some bleeding

http://www.brickshelf.com/gallery/timgould/LDraw/Review/30535002.png


======================================================================
At Mon Mar 11 19:30:08 2013, a new version of the file was submitted.
Submitted by: mikeheide
Comments:
Please let it go now. Very much too long on the PT.

Existing certification-votes were deleted.
======================================================================
At Tue Mar 12 10:25:02 2013, the following review was posted:

Reviewer: MMR1988
Certification: hold
Comments:
I really don't want to say this, but please have a look at outermost left and right condline in the housing. It is a bit to short. (OK thats nitpicking)

But if you look a bit up/down there are all in all 4 crosspieces where the edgeline to the inner housing area is missing. (this is the hold reason)